Integrity Field Guide Damage mechanisms, fitness-for-service, and the inspection methods that find them
Pigging calculator Equipment & vendors Pipe & fittings All articles Open the guide

MAWP, MAP and design pressure: what each one means

These come up in every API 510 and 570 examination and in every re-rating discussion, and they are genuinely distinct. The difference is which thickness and which allowances go into the calculation.

API 5796 min read
A scraper pig on display at the Trans-Alaska Pipeline. The cups seal against the wall; the flow behind them is what moves it.
A scraper pig on display at the Trans-Alaska Pipeline. The cups seal against the wall; the flow behind them is what moves it.Trans-Alaska Pipeline System Visitors Center Scraper Pig — Leijurv,
Guide › Articles › API 579
wall thinned evenly across the whole surface
Uniform wall loss, and what it does to MAWPFrom the damage mechanism library →
A 1971 photograph of the Gulf refinery at Rozenburg in the Netherlands, showing process units and storage under a wide sky.
Rozenburg, 1971. Much of the plant still running was built to the codes of this era — which is why fitness-for-service exists.

All three are pressures. They are calculated from different thicknesses, for different purposes, and they answer different questions.

Design pressure

What it is: the pressure the purchaser specified when the equipment was ordered. An input, not a result.

The designer takes it, adds temperature, material and geometry, and calculates a required thickness — then adds corrosion allowance and rounds up to a plate size that can actually be bought. So the vessel as built is usually somewhat thicker than the design pressure strictly required.

It never changes. It is a specification, and it is what appears on the nameplate alongside the rated conditions.

MAWP — maximum allowable working pressure

What it is: the maximum pressure the equipment is permitted to operate at, calculated from the actual current thickness less any future corrosion allowance, in the corroded condition, at the design temperature.

This is the number that matters in service, and it is the one that falls as the equipment corrodes.

A new vessel typically has a MAWP above its design pressure, because of that rounding up to a standard plate thickness. As corrosion consumes the extra, MAWP falls. When it reaches design pressure, the margin from rounding is gone. When it would fall below, the equipment must be repaired, replaced, or re-rated to the lower pressure.

Two details that catch people out:

MAP — maximum allowable pressure

What it is: the maximum pressure the equipment could hold in the new and cold condition — full nominal thickness, no corrosion allowance deducted, at ambient temperature.

It is the theoretical ceiling for that geometry and material. Always the highest of the three.

What it is used for: establishing hydrotest pressure, and understanding how much margin existed at the start. It is not an operating limit and nobody operates to it.

A refinery at night; every line in it is on an inspection plan.
A refinery at night; every line in it is on an inspection plan.Anacortes Refinery 31911 — Walter Siegmund (talk),

Side by side

Design pressureMAWPMAP
Thickness usedSpecified, not measuredActual, less future corrosionNominal, new
Corrosion allowanceAdded on topDeductedNot deducted
TemperatureDesignDesignAmbient
Changes over timeNoYes — it fallsNo
Relative sizeLowest of the three, usuallyMiddleHighest
Used forSpecificationThe operating limitHydrotest, reference

Worked through

A vessel designed for 20 bar. Calculation says 9.4 mm is required; add 3 mm corrosion allowance and buy 12.7 mm plate.

At that point the options are the usual four: reduce the future corrosion allowance if the inspection interval justifies it, repair, replace, or re-rate to the pressure the remaining wall supports.

Re-rating is an engineering answer, not a failure

If the process never needs 20 bar — and many vessels operate far below their rating — re-rating to 16 bar may be entirely acceptable and costs nothing but the paperwork and a nameplate change. It is frequently the cheapest legitimate outcome of an assessment, and it is one of the remediation options API 579 explicitly lists.

Where this connects to fitness-for-service

When a flaw is found, one of the standard outputs of an API 579 assessment is a reduced MAWP — the pressure at which the damaged component still has acceptable margin.

For local metal loss the link is direct: the remaining strength factor scales the acceptable pressure. If the calculated RSF is below the acceptance value of 0.90, the component can be operated at a pressure reduced in proportion, rather than being condemned. That is the same re-rating decision, arrived at through the assessment.

Which is why MAWP, not design pressure, is the number an integrity engineer tracks. Design pressure tells you what somebody wanted in 1987. MAWP tells you what the metal in front of you can actually do.

Try it

Calculate MAWP from your own numbers

The quick check takes thickness, diameter and material and returns the minimum required thickness and the MAWP the remaining wall supports.

Open the quick check
Read next

Who writes this. A mechanical engineer with twelve years in oil and gas — in-line inspection, fired heater and furnace inspection, and pipeline integrity. What is here comes from the published standards and from what those years in the field actually looked like. It is not written by an API-certified inspector.

This is not an assessment. Nothing on this site may be used to justify a decision about real equipment. Assessing plant requires the current editions of the applicable codes, data from a licensed source, and a competent engineer who signs for the answer. · Integrity Field Guide · Pipeline pigging calculator · Pigging equipment & vendor directory · Pipe & fitting dimensions

Pictures: “Acid-corrosion-in-a-flue-gas-duct-01” by CEphoto, Uwe Aranas, CC BY-SA 3.0, via Wikimedia Commons; “Anacortes Refinery 31911” by Walter Siegmund (talk), CC BY 2.5, via Wikimedia Commons; “United States Strategic Petroleum Reserve 072” by ENERGY.GOV, public domain, via Wikimedia Commons; “Trans-Alaska Pipeline System Visitors Center Scraper Pig” by Leijurv, CC BY-SA 4.0, via Wikimedia Commons; “Gulf raffinaderij, Rozenburg, Bestanddeelnr 924-8259” by Hans Peters for Anefo, CC0, via Wikimedia Commons.